DC 3.6V-6V в 50KV 20000V 500KV 1000KV Step Up Power Module High Voltage Generator Ignition Coil Pulse Arc on - Модуль питания повышения напряжения от 3,6 В до 6 В до 50 кВ, 20000 В, 500 кВ, 1000 кВ с высоким напряжением, генератором искрообразования с пул

DC 3.6V-6V в 50KV 20000V 500KV 1000KV Step Up Power Module High Voltage Generator Ignition Coil Pulse Arc on - Модуль питания повышения напряжения от 3 6 В до 50 кВ 20000 500 1000 с высоким напряжением генератором искрообразования пул

Features:

Double high-voltage cables can be ignited by cigarette paper, and a
high-voltage line is available at Metallkoerper to support current and
no sound.
The module can be used as high school scientific experiment
equipment, electronic equipment, negative ion generator, used for
scientific hours using high voltage source.
About performance:
Single 18650 or idle mobile phone battery (remove the protection board, the position above 2000mAh, planned capacity).

Precautions for module use

1. High-voltage modules should avoid using high-voltage no-load, and the power supply mustAdjust before the end of the appropriate distance of the high-voltage line, high-voltage wire drawingThe distance is proportional to the voltage and capacity of the battery used.

2. In the short to long experiment, test the arc distance when the power supply is prohibitedBeyond the longest arc distance, because high-voltage energy cannot be released,It is easy to damage the module.

3. When the module is powered, the internal heat is not hot, so it does not take a long time to work.

product description:
1. Model: MC-105
2. Length: 64 mm
3. Diameter: 24 mm
Plane diameter: 21mm
5. Input voltage: DC 3.7-6V
Input current: 2A-3A
Input wire length: 10cm
8. High voltage form: pulse DC type
9. Output voltage: 50kVOutput current: 0.05A
11. Length of output line: 8cm
12. High voltage polarization discharge distance: 1-2cm
13. Usage: red and green lines are input ports, red line is positive, green line is negative, the other two high-voltage lines are output ports; fixed high-voltage line ports are at an appropriate distance; input port and battery can be connected to achieve high voltage arc
14. Input power: You can use a single 3.7V lithium battery or 2S in parallel, such as 18650 battery, etc.

Package Included:
1 x 50kV high voltage pulse generator super arc pulse ignition coil module

20000V

Input voltage: DC 12V

Output voltage: 15000V-20000V adjustable

Rated power: 5W

Mounting hole diameter: 5mm

Hole center distance: 112mm

Size: 60 * 70 * 30mm

Note: The red and black wires are small inputs, the red is the 12V power supply positive input, the black is the negative input, the thick red wire is the high voltage positive output, and the thick black wire is the high voltage negative output.

Package Included:1PCS x DC 12V to 20000V high voltage electrostatic generator negative ion generator

500KV

DC12V DC high voltage pulse generator module ignition coil capacitance arc distance 50mm
12V input, good power, quality, arcing distance, sound shocking, simple operation

Specifications:
Peripheral circuit is simple (just plug in switches, batteries can be) the discharge intensity violent.
Module Model: MCY-12-1
Physical volume: Length 70X 32mm diameter
Input voltage: 6V-12V
Input Current: 0.5A-1A
Input line length: 23 cm
High voltage type: DC type pulse
Output voltage: about 500KV (please pay attention to safety when used)
Output Current: 0.5A-1A
Output line length: about 92 cm
High voltage bipolar discharge distance: 2 cm -5 cm

Features:
This module is a science of small production with high voltage inverter transformer / booster finished module
After
the input terminal DC6V-12V voltage can get tens of thousands of volts
of direct current high voltage at the output,It can be used for high
school science experiment, electronic equipment, negative ion generator,
high voltage source when using scientific small production,Module uses
the Tesla coil principle is made,
the output high voltage pulse current, small size, high efficiency

Usage:
1. To avoid the use of electricity at high voltage load, must adjust the proper distance
between the front end of the high-voltage power-
2. To test the arc distance from short to long experiment, when power is strictly prohibited exceed
the maximum arcing distance, energy can not be released due to high pressure, easy to damage the module.
3. Power module, the internal should not heat, so we can not work long hours.
4. Determine whether the battery capacity can drive maximum power output of the battery
voltage measurement approach is arcing time. If 6V or so you can output the maximum power.
5. Two small-capacity lithium series is 7.2V, measured in arc-state voltage has dropped to about 4V,
the capacity of the smaller voltage pull lower. It is proposed to use lithium 2000MA above,
the best conditions with more battery 4000MA.

Package includes:
1x DC12V pulse high-voltage module

1000KV

Product Specifications:
Module type: MC-901
Input voltage: 3.7V-7.4V
Input current: 0.5A-1A
Input wire length: 9 cm
High voltage: pulse DC type
Output voltage: 800KV-1000KV (please pay attention to safety when using)
Output current: 0.5A-1A
Output length: approximately 16 cm
High voltage bipolar discharge distance 1.5cm-2cm
Size: 88x26mm (LXD)

Precautions for using the module:
1. The high-voltage module should avoid using high-voltage no-load, the power supply must
Adjust the high-voltage line of the appropriate distance before the end, high-voltage wire drawing
The distance is proportional to the voltage and capacity of the battery used.
2. From short to long experiments, test the arc distance when the power supply is prohibited
Exceeding the longest arc distance, due to the high voltage energy cannot be released,
It is easy to damage the module.
3. When the module is powered, the internal heat is not hot, so it does not work for a long time.

Package Included:
1XHigh voltage inverter